Zum Hauptinhalt gehen

Modbus Adress list for Section OEM: ABB/NEWAVE UPS Type Concept Power

Aktualisiert

 

Address Type Function Name Description Length
This is the general UPS modbus address list. It uses the address range 100 – 183:
100 U 3 / 4 OUTP0WER0 Outpower Phase 1 % 1
101 U 3 / 4 OUTP0WER1 Outpower Phase 2 % 1
102 U 3 / 4 OUTP0WER2 Outpower Phase 3 % 1
103 U 3 / 4 BATTCAP Battery Capacity % 1
104 S 3 / 4 INVOLT0 Input Voltage Phase 1 V 1
105 S 3 / 4 INVOLT1 Input Voltage Phase 2 V 1
106 S 3 / 4 INVOLT2 Input Voltage Phase 3 V 1
107 S 3 / 4 TEMPDEG Temperature C° 1
108 S 3 / 4 AUTONOMTIME Autonomy Time minutes 1
109 U 3 / 4 STATUS (e. g. 
UPS normal = “4”,
Powerfail = “12”,
Battery test running = “68”, Bypass = “5” ) 		UPS Status (ASCII HEX) Please note UPSMAN status bytes table below 1
110 S 3 / 4 BATTVOLT Battery Voltage V 1
111 U 3 / 4 INFREQ0 Input Frequency Hz Phase 1 1
112 U 3 / 4 INFREQ1 Input Frequency Hz Phase 2 1
113 U 3 / 4 INFREQ2 Input Frequency Hz Phase 3 1
114 U 3 / 4 CNT_PF Powerfail Counter 1
115 U 3 / 4 Alarm Battery Bad 1 =  active; 0 = not active 1
116 U 3 / 4 Alarm: On Battery 1 = active; 0 = not active 1
117 U 3 / 4 Alarm: Battery Low 1 = active; 0 = not active 1
118 U 3 / 4 Alarm: Battery Depleted 1 = active; 0 = not active 1
119 U 3 / 4 Alarm: Over temperature 1 = active; 0 = not active 1
120 U 3 / 4 Alarm: Input Bad 1 = active; 0 = not active 1
121 U 3 / 4 Alarm: Output Bad 1 = active; 0 = not active 1
122 U 3 / 4 Alarm: Output Overload 1 = active; 0 = not active 1
123 U 3 / 4 Alarm: On Bypass 1 = active; 0 = not active 1
124 U 3 / 4 Alarm: Bypass Bad 1 = active; 0 = not active 1
125 U 3 / 4 Alarm: Output Off as requested. 1 = active; 0 = not active 1
126 U 3 / 4 Alarm: UPS Off as requested. 1 = active; 0 = not active 1
127 U 3 / 4 Alarm: Charger Failed 1 = active; 0 = not active 1
128 U 3 / 4 Alarm: UPS Output Off 1 = active; 0 = not active 1
129 U 3 / 4 Alarm: UPS System Off 1 = active; 0 = not active 1
130 U 3 / 4 Alarm: Fan Failure 1 = active; 0 = not active 1
131 U 3 / 4 Alarm: fuse failure 1 = active; 0 = not active 1
132 U 3 / 4 Alarm: general fault 1 = active; 0 = not active 1
133 U 3 / 4 Alarm: diagnose test failed 1 = active; 0 = not active 1
134 U 3 / 4 Alarm: communication  lost 1 = active; 0 = not active 1
135 U 3 / 4 Alarm: awaiting power 1 = active; 0 = not active 1
136 U 3 / 4 Alarm: shutdown pending 1 = active; 0 = not active 1
137 U 3 / 4 Alarm: shutdown imminent 1 = active; 0 = not active 1
138 U 3 / 4 Alarm: test in progress 1 = active; 0 = not active 1
139 U 3 / 4 Manual Bypass Switch Closed

0 = open

1 = closed

 1
140 U 3 / 4 OUTPUT_VOLT0 Outputvoltage Phase 1 1
141 U 3 / 4 OUTPUT_VOLT1 Outputvoltage Phase 2 1
142 U 3 / 4 OUTPUT_VOLT2 Outputvoltage Phase 3 1
143 U 3 / 4 OutputCurrent Phase A * 10 Output Current Phase 1 in Ampere devided by 10 1
144 U 3 / 4 OutputCurrent Phase B * 10 Output Current Phase 1 in Ampere devided by 10 1
145 U 3 / 4 OutputCurrent Phase C * 10 Output Current Phase 1 in Ampere devided by10 1
146 U 3 / 4 xid3017 Bits 0-15 Statusbit, for details please contact NEWAVE 1
147 U 3 / 4 xid3017 Bits 16-31 

 		 Statusbit, for details please contact ABB/NEWAVE 1
148 U 3 / 4 xid645 Bits 0-15 Alarmbit, for details  please contact ABB/NEWAVE 1
149 U 3 / 4 xid645 Bits 16-31 Alarmbit, for details  please contact ABB/NEWAVE 1
150 U 3 / 4 xid645 Bits 32-47 Alarmbit, for details  please contact ABB/NEWAVE 1
151 U 3 / 4 xid645 Bits 48-63 Alarmbit, for details  please contact ABB/NEWAVE 1
152 U 3 / 4 Sensormanager/SMTCOM sensor 1 Analog value 1
153 U 3 / 4 Sensormanager/SMTHCOM sensor 2 Analog value 1
154 U 3 / 4 Sensormanager  sensor 3 Analog value 1
155 U 3 / 4 Sensormanager sensor 4 Analog value 1
156 U 3 / 4 Sensormanager sensor 5 Analog value 1
157 U 3 / 4 Sensormanager sensor 6 Analog value 1
158 U 3 / 4 Sensormanager  sensor 7 Analog value 1
159 U 3 / 4 Sensormanager  sensor 8 Analog value 1
160 U 3 / 4 TrueOutputPower  Phase A in KW True Output Power Current Phase 1 in Kilowatt 1
161 U 3 / 4 TrueOutputPower  Phase A in KW True Output Power Current Phase 1 in Kilowatt 1
162 U 3 / 4 TrueOutputPower  Phase A in KW True Output Power Current Phase 1 in Kilowatt 1
163 U 3 / 4 AUX Port 1 1 = active (high), 0 = not active (low) 1
164 U 3 / 4 AUX Port 2 1 = active (high), 0 = not active (low) 1
165 U 3 / 4 AUX Port 3 1 = active (high), 0 = not active (low) 1
166 U 3 / 4 AUX Port 4 1 = active (high), 0 = not active (low) 1
167 U 3 / 4 BATTERYCURRENT Battery Current in Ampere 1
168 U 3 / 4 OUTFREQ0 Output Frequency Phase 1 in Hz 1
169 U 3 / 4 UPSIDMASK&0xFFFF for details  please contact NEWAVE 1
170 U 3 / 4 (UPSIDMASK&0xFFFF0000)>>16 for details  please contact NEWAVE 1
171 U 3 / 4 AUXINPFREQ0 Auxiliary Input Frequency Phase 1 1
172 U 3 / 4 AUXINPFREQ1 Auxiliary Input Frequency Phase 2 1
173 U 3 / 4 AUXINPFREQ2 Auxiliary Input Frequency Phase 3 1
174 U 3 / 4 AUXINPVOLT0 Auxiliary Input Voltage Phase 1 1
175 U 3 / 4 AUXINPVOLT1 Auxiliary Input Voltage Phase 2 1
176 U 3 / 4 AUXINPVOLT2 Auxiliary Input Voltage Phase 3 1
177 U 3 / 4 BP_FREQ0 Bypass Frequency 1
178 U 3 / 4 BP_VOLT0 Bypass Voltage Phase 1 1
179 U 3 / 4 BP_VOLT1 Bypass Voltage Phase 1 1
180 U 3 / 4 BP_VOLT2 Bypass Voltage Phase 3 1
181 U 3 / 4 (RAWSTATEB&0x8)!=0x8 Statusbit, for details please contact ABB/NEWAVE 1
182 U 3 / 4 SolaBCOND Battery Condition: 0=good, 1=weak, 2=replace 1
183 U 3 / 4 CONCE_IDENT String Identifying the UPS 1

Note for systems with more then one installed UPS module:

Starting from register 30100, all values coming from the single module #1 are stored sequentially, according to the sequence adopted for registers 100…166. The values from Module #2 are stored starting at register address 30200 and so forth, until the last module #30 ranging from 33000 … 33066.

UPS MODULE 1: 30100 - 30166
30100 U 3 / 4 OUTP0WER0 Outpower Phase 1 % 1
30101 U 3 / 4 OUTP0WER1 Outpower Phase 2 % 1
30102 U 3 / 4 OUTP0WER2 Outpower Phase 3 % 1
30103 U 3 / 4 BATTCAP Battery Capacity % 1
30104 S 3 / 4 INVOLT0 Input Voltage Phase 1 V 1
30105 S 3 / 4 INVOLT1 Input Voltage Phase 2 V 1
30106 S 3 / 4 INVOLT2 Input Voltage Phase 3 V 1
30107 S 3 / 4 TEMPDEG Temperature C° 1
30108 S 3 / 4 AUTONOMTIME Autonomy Time minutes 1
30109 U 3 / 4 STATUS (e. g. 
UPS normal = “4”,
Powerfail = “12”,
Battery test running = “68”, Bypass = “5” ) 		UPS Status (ASCII HEX) Please note UPSMAN status bytes table below 1
30110 S 3 / 4 BATTVOLT Battery Voltage V 1
30111 U 3 / 4 INFREQ0 Input Frequency Hz Phase 1 1
30112 U 3 / 4 INFREQ1 Input Frequency Hz Phase 2 1
30113 U 3 / 4 INFREQ2 Input Frequency Hz Phase 3 1
30114 U 3 / 4 CNT_PF Powerfail Counter 1
30115 U 3 / 4 Alarm Battery Bad 1 =  active; 0 = not active 1
30116 U 3 / 4 Alarm: On Battery 1 = active; 0 = not active 1
30117 U 3 / 4 Alarm: Battery Low 1 = active; 0 = not active 1
30118 U 3 / 4 Alarm: Battery Depleted 1 = active; 0 = not active 1
30119 U 3 / 4 Alarm: Over temperature 1 = active; 0 = not active 1
30120 U 3 / 4 Alarm: Input Bad 1 = active; 0 = not active 1
30121 U 3 / 4 Alarm: Output Bad 1 = active; 0 = not active 1
30122 U 3 / 4 Alarm: Output Overload 1 = active; 0 = not active 1
30123 U 3 / 4 Alarm: On Bypass 1 = active; 0 = not active 1
30124 U 3 / 4 Alarm: Bypass Bad 1 = active; 0 = not active 1
30125 U 3 / 4 Alarm: Output Off as requested. 1 = active; 0 = not active 1
[…] continue until […]
30160 U 3 / 4 TrueOutputPower  Phase A in KW True Output Power Current Phase 1 in Kilowatt 1
30161 U 3 / 4 TrueOutputPower  Phase A in KW True Output Power Current Phase 1 in Kilowatt 1
30162 U 3 / 4 TrueOutputPower  Phase A in KW True Output Power Current Phase 1 in Kilowatt 1
30163 U 3 / 4 AUX Port 1 1 = active (high), 0 = not active (low) 1
30164 U 3 / 4 AUX Port 2 1 = active (high), 0 = not active (low) 1
30165 U 3 / 4 AUX Port 3 1 = active (high), 0 = not active (low) 1
30166 U 3 / 4 AUX Port 4 1 = active (high), 0 = not active (low) 1
UPS MODULE 2: 30200 - 30266
30200 U 3 / 4 OUTP0WER0 Outpower Phase 1 % 1
30201 U 3 / 4 OUTP0WER1 Outpower Phase 2 % 1
30202 U 3 / 4 OUTP0WER2 Outpower Phase 3 % 1
30203 U 3 / 4 BATTCAP Battery Capacity % 1
30204 S 3 / 4 INVOLT0 Input Voltage Phase 1 V 1
30205 S 3 / 4 INVOLT1 Input Voltage Phase 2 V 1
30206 S 3 / 4 INVOLT2 Input Voltage Phase 3 V 1
30207 S 3 / 4 TEMPDEG Temperature C° 1
30208 S 3 / 4 AUTONOMTIME Autonomy Time minutes 1
30209 U 3 / 4 STATUS (e. g. 
UPS normal = “4”,
Powerfail = “12”,
Battery test running = “68”, Bypass = “5” ) 		UPS Status (ASCII HEX) Please note UPSMAN status bytes table below 1
30210 S 3 / 4 BATTVOLT Battery Voltage V 1
30211 U 3 / 4 INFREQ0 Input Frequency Hz Phase 1 1
30212 U 3 / 4 INFREQ1 Input Frequency Hz Phase 2 1
30213 U 3 / 4 INFREQ2 Input Frequency Hz Phase 3 1
30214 U 3 / 4 CNT_PF Powerfail Counter 1
30215 U 3 / 4 Alarm Battery Bad 1 =  active; 0 = not active 1
30216 U 3 / 4 Alarm: On Battery 1 = active; 0 = not active 1
30217 U 3 / 4 Alarm: Battery Low 1 = active; 0 = not active 1
30218 U 3 / 4 Alarm: Battery Depleted 1 = active; 0 = not active 1
30219 U 3 / 4 Alarm: Over temperature 1 = active; 0 = not active 1
30220 U 3 / 4 Alarm: Input Bad 1 = active; 0 = not active 1
30221 U 3 / 4 Alarm: Output Bad 1 = active; 0 = not active 1
30222 U 3 / 4 Alarm: Output Overload 1 = active; 0 = not active 1
30223 U 3 / 4 Alarm: On Bypass 1 = active; 0 = not active 1
30224 U 3 / 4 Alarm: Bypass Bad 1 = active; 0 = not active 1
30225 U 3 / 4 Alarm: Output Off as requested. 1 = active; 0 = not active 1
[…] continue until […]
30261 U 3 / 4 TrueOutputPower  Phase A in KW True Output Power Current Phase 1 in Kilowatt 1
30262 U 3 / 4 TrueOutputPower  Phase A in KW True Output Power Current Phase 1 in Kilowatt 1
30263 U 3 / 4 AUX Port 1 1 = active (high), 0 = not active (low) 1
30264 U 3 / 4 AUX Port 2 1 = active (high), 0 = not active (low) 1
30265 U 3 / 4 AUX Port 3 1 = active (high), 0 = not active (low) 1
30266 U 3 / 4 AUX Port 4 1 = active (high), 0 = not active (low) 1
UPS Module 3: 30300 - 30366
30300 U 3 / 4 OUTP0WER0 Outpower Phase 1 % 1
30301 U 3 / 4 OUTP0WER1 Outpower Phase 2 % 1
30302 U 3 / 4 OUTP0WER2 Outpower Phase 3 % 1
30303 U 3 / 4 BATTCAP Battery Capacity % 1
30304 S 3 / 4 INVOLT0 Input Voltage Phase 1 V 1
30305 S 3 / 4 INVOLT1 Input Voltage Phase 2 V 1
30306 S 3 / 4 INVOLT2 Input Voltage Phase 3 V 1
30307 S 3 / 4 TEMPDEG Temperature C° 1
30308 S 3 / 4 AUTONOMTIME Autonomy Time minutes 1
30309 U 3 / 4 STATUS (e. g. 
UPS normal = “4”,
Powerfail = “12”,
Battery test running = “68”, Bypass = “5” ) 		UPS Status (ASCII HEX) Please note UPSMAN status bytes table below 1
30310 S 3 / 4 BATTVOLT Battery Voltage V 1
30311 U 3 / 4 INFREQ0 Input Frequency Hz Phase 1 1
30312 U 3 / 4 INFREQ1 Input Frequency Hz Phase 2 1
30213 U 3 / 4 INFREQ2 Input Frequency Hz Phase 3 1
30314 U 3 / 4 CNT_PF Powerfail Counter 1
30315 U 3 / 4 Alarm Battery Bad 1 =  active; 0 = not active 1
[…] continue until […]
30361 U 3 / 4 TrueOutputPower  Phase A in KW True Output Power Current Phase 1 in Kilowatt 1
30362 U 3 / 4 TrueOutputPower  Phase A in KW True Output Power Current Phase 1 in Kilowatt 1
30363 U 3 / 4 AUX Port 1 1 = active (high), 0 = not active (low) 1
30364 U 3 / 4 AUX Port 2 1 = active (high), 0 = not active (low) 1
30365 U 3 / 4 AUX Port 3 1 = active (high), 0 = not active (low) 1
30366 U 3 / 4 AUX Port 4 1 = active (high), 0 = not active (low) 1
UPS Module 4: 30400 - 30466
30400 U 3 / 4 OUTP0WER0 Outpower Phase 1 % 1
30401 U 3 / 4 OUTP0WER1 Outpower Phase 2 % 1
30402 U 3 / 4 OUTP0WER2 Outpower Phase 3 % 1
30403 U 3 / 4 BATTCAP Battery Capacity % 1
30404 S 3 / 4 INVOLT0 Input Voltage Phase 1 V 1
30405 S 3 / 4 INVOLT1 Input Voltage Phase 2 V 1
30406 S 3 / 4 INVOLT2 Input Voltage Phase 3 V 1
30407 S 3 / 4 TEMPDEG Temperature C° 1
30408 S 3 / 4 AUTONOMTIME Autonomy Time minutes 1
30409 U 3 / 4 STATUS (e. g. 
UPS normal = “4”,
Powerfail = “12”,
Battery test running = “68”, Bypass = “5” ) 		UPS Status (ASCII HEX) Please note UPSMAN status bytes table below 1
30410 S 3 / 4 BATTVOLT Battery Voltage V 1
[…] cuntinue until […]
30460 U 3 / 4 TrueOutputPower  Phase A in KW True Output Power Current Phase 1 in Kilowatt 1
30461 U 3 / 4 TrueOutputPower  Phase A in KW True Output Power Current Phase 1 in Kilowatt 1
30462 U 3 / 4 TrueOutputPower  Phase A in KW True Output Power Current Phase 1 in Kilowatt 1
30463 U 3 / 4 AUX Port 1 1 = active (high), 0 = not active (low) 1
30464 U 3 / 4 AUX Port 2 1 = active (high), 0 = not active (low) 1
30465 U 3 / 4 AUX Port 3 1 = active (high), 0 = not active (low) 1
30466 U 3 / 4 AUX Port 4 1 = active (high), 0 = not active (low) 1
UPS Module 5: 30500 - 30566
30500 U 3 / 4 OUTP0WER0 Outpower Phase 1 % 1
30501 U 3 / 4 OUTP0WER1 Outpower Phase 2 % 1
30502 U 3 / 4 OUTP0WER2 Outpower Phase 3 % 1
30503 U 3 / 4 BATTCAP Battery Capacity % 1
30504 S 3 / 4 INVOLT0 Input Voltage Phase 1 V 1
30505 S 3 / 4 INVOLT1 Input Voltage Phase 2 V 1
[…] continue until […]
30563 U 3 / 4 AUX Port 1 1 = active (high), 0 = not active (low) 1
30564 U 3 / 4 AUX Port 2 1 = active (high), 0 = not active (low) 1
30565 U 3 / 4 AUX Port 3 1 = active (high), 0 = not active (low) 1
30566 U 3 / 4 AUX Port 4 1 = active (high), 0 = not active (low) 1
The address range of the UPS Modules 6 – 30 follows as seen above:
UPS Module 6: 30600 - 30666
UPS Module 7: 30700 – 30766
UPS Module 8: 30800 – 30866
UPS Module 9: 30900 – 30966
UPS Module 10: 31000 - 31066
UPS Module 11: 31100 – 31166
UPS Module 12: 31200 – 31266
UPS Module 13: 31300 – 31366
UPS Module 14: 31400 – 31466
UPS Module 15: 31500 – 31566
UPS Module 16: 31600 – 31666
UPS Module 17: 31700 – 31766
UPS Module 18: 31800 – 31866
UPS Module 19: 31900 – 31966
UPS Module 20: 32000 – 31266
UPS Module 21: 32100 – 32166
UPS Module 22: 32200 – 32266
UPS Module 23: 32300 – 32366
UPS Module 24: 32400 – 32466
UPS Module 25: 32500 – 32566
UPS Module 26: 32600 – 32666
UPS Module 27:32700 – 32766
UPS Module 28: 32800 – 32866
UPS Module 29: 32900 – 32966
UPS Module 30: 33000 – 33066

 

Verwandte Beiträge

Kommentare

0 Kommentare

Bitte melden Sie sich an, um einen Kommentar zu hinterlassen.